Menu
Search
Filters
Close
Menu

Currie 44 - Jeep Wrangler JL Front Axle Assembly

Need Product Quickly?

 

Call us at (714) 528-6957 Ext 122

or email us at offroad@currieenterprises.com

We'll check with our authorized distributors to see if they have stock. 

 

Electric Locker & Wiring Notice

 

Using the factory Rubicon Locker switch with an aftermarket wiring harness adapter does not supply adequate voltage to operate the electric locker and will void the locker warranty.

 

Recommended Gearing By Tire Size
Engine 35" Tire 37" Tire 39" Tire* 40" Tire*
Gas 4.88
Gears		 5.13
Gears		 5.38
Gears		 5.38
Gears
Diesel 4.10
Gears		 4.56
Gears		 4.56
Gears		 4.88
Gears

Gear ratio suggestions are based on mixed highway and off-road usage. Please contact a Currie specialist at (714) 528-6957 if you have any questions.

 

* Currie does not recommend using tires 39" and larger with the factory front unit bearings and ball joints. 

 

The Currie 44 front axle assembly is a direct bolt-in assembly for 2018 and newer Jeep Wrangler JL Vehicles. Featuring Rubicon width for tire clearance, a significantly stronger center casting, axle tubes, forged knuckles, and chromoly axles, the Currie 44 is designed for heavy off-road with up to 37-inch tall tires.


Currie 44 Features:

  • Direct Bolt-in Fit for Wrangler JL
  • 68 in. JL Rubicon Width (+1.5 in. Over Non-Rubicon Models)
  • Currie High-Pinion Reinforced Center Section
  • 3 in. Diameter, .5 in. Wall DOM Axle Tubes
  • Currie Forged JL Inner Knuckles
  • 4340 Chromoly Axles Inner and Outer Axles
  • Steering Geometry and Brackets Setup for Lifted Vehicles
  • Uses Proven and Readily Available JK 44 Gears and Locker
  • Satin Black Powder Coat Finish for Long Lasting Protection
  • Retains the Vehicle's Stock Steering Knuckle Assemblies, Brakes, and Wheels
  • Requires Rubicon Width Tie Rod

*** SELECT OPTIONS TO BUILD AND PRICE ***

*
*
*
$5,850.00

The Currie 44 front axle assembly is a direct bolt-in solution that reduces the overall cost by enabling you to retain the complete stock JL outer knuckle assemblies (brakes, hubs, etc.), steering, and stock wheel bolt pattern.

 

Currie 44 Features

  Currie 44 high-pinion nodular iron center section features 14 lbs of reinforcement over a stock 44 with thicker walls and webbing to deliver superior strength and rigidity
     
  Large 3-in. diameter x .5-in. wall axle tubes (left) are more than 2.5 times stronger than the stock tubes (right)
     
  Currie heavy-duty forged inner knuckles (right) are massively more robust than the stock knuckles (left) and are designed for severe off-road use with tall tires
     
  Currie Performance 4340 chromoly axles provide superior end-to-end strength over OEM carbon steel axles. Black oxide coating helps protect from surface corrosion for improved durability
     
 

Lower control arm mounts are one-piece construction with integrated skid plates to help fend off bracket-seeking rocks
     
  Included pinion flange allows the factory driveshaft to be used without modification
     
  Rock-proof Currie nodular iron front cover protects expensive internals and adds structural support to the housing's face flange
     
Powder Coat   UV Stable Satin black powder coat finish adds long-lasting protection against rust and corrosion to keep your Currie 44 looking its best

 

 

Notes

Computer Programming: 2012 and newer vehicles require a computer programmer, such as the AEV ProCal Module, to reset the gear ratio and tire height in the vehicle's computer for the proper function of the vehicle's stability control and transmission shift points

Outer Knuckle Assemblies: The Currie 44 is designed to reuse the complete stock JLouter knuckle assemblies from the ball joints out (knuckles, hubs, disk brake calipers, and rotors)

Overall Width: Axle width is 68.0 inches (stock JK width) between wheel mounting surfaces

Tire Size: Recommended maximum 37-inch tire size due to the inherent limitations of the stock brakes, wheel bearings, and axle u-joints

 

 

The Currie 44 front axle assembly is a direct bolt-in solution that reduces the overall cost by enabling you to retain the complete stock JL outer knuckle assemblies (brakes, hubs, etc.), steering, and stock wheel bolt pattern.

 

Currie 44 Features

  Currie 44 high-pinion nodular iron center section features 14 lbs of reinforcement over a stock 44 with thicker walls and webbing to deliver superior strength and rigidity
     
  Large 3-in. diameter x .5-in. wall axle tubes (left) are more than 2.5 times stronger than the stock tubes (right)
     
  Currie heavy-duty forged inner knuckles (right) are massively more robust than the stock knuckles (left) and are designed for severe off-road use with tall tires
     
  Currie Performance 4340 chromoly axles provide superior end-to-end strength over OEM carbon steel axles. Black oxide coating helps protect from surface corrosion for improved durability
     
 

Lower control arm mounts are one-piece construction with integrated skid plates to help fend off bracket-seeking rocks
     
  Included pinion flange allows the factory driveshaft to be used without modification
     
  Rock-proof Currie nodular iron front cover protects expensive internals and adds structural support to the housing's face flange
     
Powder Coat   UV Stable Satin black powder coat finish adds long-lasting protection against rust and corrosion to keep your Currie 44 looking its best

 

 

Notes

Computer Programming: 2012 and newer vehicles require a computer programmer, such as the AEV ProCal Module, to reset the gear ratio and tire height in the vehicle's computer for the proper function of the vehicle's stability control and transmission shift points

Outer Knuckle Assemblies: The Currie 44 is designed to reuse the complete stock JLouter knuckle assemblies from the ball joints out (knuckles, hubs, disk brake calipers, and rotors)

Overall Width: Axle width is 68.0 inches (stock JK width) between wheel mounting surfaces

Tire Size: Recommended maximum 37-inch tire size due to the inherent limitations of the stock brakes, wheel bearings, and axle u-joints

 

 

Products specifications
Center Section Currie 44 high-pinion nodular-iron center section with thicker walls and webbing
Gear Set Larger/stronger Dana 44 8.8” late model JK ring and pinion set
Pinion Yoke 1310 (stock size) pinion companion flange
Differential Cover Currie nodular-iron cover with gasketed fill plug with dip stick
End Forgings Currie heavy-duty forged steel inner C’s
Axle Tubes 3 in. diameter, .5 wall DOM tube
Axles Currie Performance 4340 chromoly 30/32-spline inner/outer axles
Suspension Brackets Heavy gauge 3/16” laser cut steel brackets
Control Arm Mounts Upper control and lower control arm mounts are 3/16 thick, one-piece construction; lower mounts feature an integrated skid plate
Geometry Optimized for stock height or lifted vehicles with 5 degrees of pinion angle to reduce driveshaft angle and 5 degrees of caster for improved steering
Width 68-inches between wheel mounting surfaces (stock JL Ribicon width)
Wheel Bolt Pattern 5 on 5 inch with 1/2 inch studs (standard JL pattern)
Oil Capacity 1.5 quarts of 75W-140 synthetic gear oil (API GL-5 Rated)
Finish Black satin powder coat
Product tags
Related products
Currie 4x4 Performance Gear Oil

Currie 4x4 Performance Gear Oil

$17.00

High-performance full-synthetic 75W-140, GL-5 gear oil designed specifically for the requirements of 4x4 Jeeps and trucks. Currie 4x4 Performance Gear Oil provides maximum shear stability and extreme pressure protection with a superior inhibitor package that protects against rust, corrosion and foaming.


Details:

  • 100% Synthetic Formula Provides Superior Shock, Load, and Wear Protection
  • Contains an Effective Inhibitor Package that Protects Against Rust and Corrosion
  • Extreme Pressure Chemistry Delivers 4 Times the Film Strength of Conventional Gear Oils
  • Reduces Operating Temperatures and Delivers Improved Efficiency
  • 75W-140 API GL-5 Rated
Related Products
Currie 4x4 Performance Gear Oil

Currie 4x4 Performance Gear Oil

$17.00

High-performance full-synthetic 75W-140, GL-5 gear oil designed specifically for the requirements of 4x4 Jeeps and trucks. Currie 4x4 Performance Gear Oil provides maximum shear stability and extreme pressure protection with a superior inhibitor package that protects against rust, corrosion and foaming.


Details:

  • 100% Synthetic Formula Provides Superior Shock, Load, and Wear Protection
  • Contains an Effective Inhibitor Package that Protects Against Rust and Corrosion
  • Extreme Pressure Chemistry Delivers 4 Times the Film Strength of Conventional Gear Oils
  • Reduces Operating Temperatures and Delivers Improved Efficiency
  • 75W-140 API GL-5 Rated
Customers Also Purchased
Currie Corona Tee - Front

Currie "Corona" T-Shirt

$20.00 $10.00

Details:

  • Men's White Short Sleeve Crew Neck
  • Solid Color
  • Front Logo Graphic Print
Womens Braid - Front

Currie "Braid" Womens V-Neck Tank Top

$15.00

Details:

  • Women's Lilac Tank Top
  • Scoop Neckline
  • White Graphic
  • Logo Graphic Print Front
Currie Performance Tee - Front

Currie "Performance" T-Shirt

$20.00

Details:

  • Men's Black Short Sleeve Crew Neck
  • Solid Color
  • Logo Graphic Print Front and Back
Currie Emblem Hoodie - Front

Currie "Emblem" Hoodie

$25.00

Details:

  • Men's Black Hooded Pullover Sweatshirt
  • Adjustable Drawstring Hood
  • Cuffed Long Sleeves
  • Kangaroo Pouch Pocket
  • Logo Graphic Print Front and Back





Categories
Popular tags
Contacts
  • +1 714-528-6957
  • +1 (Fax) 951-549-0267
Information
Copyright © 2024 Currie 4x4. All rights reserved.